日本不卡二区,色色婷婷久久,日本免费不卡,国产一区日韩不卡欧美

當前位置:首頁-新聞資訊

鋁合金在熱處理時為什么會出現粗大晶粒

來源:http://igugo.cn/ 發布時間:2020-04-26

  一、粗大晶粒產品的原因
  1、 Causes of coarse grain products
  在一定條件下,鋁及鋁合金板、棒及鍛件在后續熱處理過程中會在組織中形成較大的再結晶晶粒。這種粗粒的存在,會降低材料的力學性能,使深沖零件的表面變得粗糙或產生沖擊裂紋。因此,獲得均勻的細晶粒結構是生產粗晶粒,具有化學成分的合金,均勻的退火體系,變形溫度?并對變形程度、固溶體熱處理溫度、加熱速度、退火溫度、保溫時間等因素進行了分析。
  Under certain conditions, large recrystallized grains will be formed in the structure of aluminum and its alloy plates, bars and forgings during the subsequent heat treatment. The existence of such coarse particles will reduce the mechanical properties of the material and make the surface of the deep drawing parts rough or produce impact cracks. Therefore, to obtain uniform fine grain structure is to produce coarse grain, alloy with chemical composition, uniform annealing system, deformation temperature. The factors such as deformation degree, solution heat treatment temperature, heating speed, annealing temperature and holding time are analyzed.

鋁板生產廠家
  二、如何減少鋁板熱處理過程中產生的粗糧
  2、 How to reduce the coarse grain produced in the heat treatment of aluminum plate
  鋁合金板材不容易變形,不容易產生粗大的晶粒。生產中減少或消除粗晶的一般原則是考慮上述因素,并根據具體情況采取適當?shù)目刂苹蛳胧?br />   Aluminum alloy plate is not easy to deform and produce coarse grains. The general principle of reducing or eliminating coarse grains in production is to consider the above factors and take appropriate control or elimination measures according to the specific situation.
  三是以3A21鋁板為例,看到粗粒的消除
  Third, take 3A21 aluminum plate as an example to see the elimination of coarse particles
  對于易產生粗晶的3A21合金退火板,可以采取以下措施來預防或消除:
  The following measures can be taken to prevent or eliminate the 3A21 alloy annealing plate which is easy to produce coarse grains:
  (1) 3A21合金半連續鑄錠高溫退火或熱軋時,溫度必須控制在500~520℃范圍內。
  (1) When 3A21 alloy semi continuous ingot is annealed or hot rolled at high temperature, the temperature must be controlled in the range of 500 ~ 520 ℃.
  (2)當Mn和Fe的總質量分?jǐn)?shù)小于1.8%時,w(Mn)=?在1.5%-1.4%時,w(Fe)>應控制0.4%,或w(Ti)=?0.1% ~ 0.2%的鈦。
  (2) When the total mass fraction of Mn and Fe is less than 1.8%, when w (MN) =? Is 1.5% - 1.4%, w (FE) > should control 0.4%, or w (TI) =? 0.1% - 0.2% titanium.
  建議在鹽浴中退火。如采用空氣爐,應盡量采用高溫快速退火。
  Annealing in a salt bath is recommended. If air furnace is adopted, high temperature and rapid annealing shall be adopted as far as possible.
  (4)在退火前,成品的加工率一定要避免達到臨界變形程度。一般來說,退火前成品的冷變形程度應控制在75%以上。
  (4) Before annealing, the processing rate of the finished product must avoid the critical deformation. Generally speaking, the degree of cold deformation of the finished product should be controlled above 75% before annealing.
  對于工業純鋁退火片材,可以采取以下措施來防止粗粒的產生:
  For industrial pure aluminum annealed sheet, the following measures can be taken to prevent the generation of coarse particles:
  (1)純鋁錠半連鑄采用350~500℃的軋制溫度為宜,軋制溫度控制在上限,軋制終溫不低于300℃
  (1) The proper rolling temperature for semi continuous casting of pure aluminum ingot is 350 ~ 500 ℃, the rolling temperature is controlled at the upper limit, and the final rolling temperature is not less than 300 ℃
  (2)退火前的冷變形程度不小于50%。
  (2) The cold deformation degree before annealing shall not be less than 50%.
  (3)宜在鹽浴中退火,而在空氣爐中退火時,應盡量提高加熱速度。
  (3) It is better to anneal in salt bath, while in air furnace, the heating speed should be increased as much as possible.
  鋁板生產廠家嚴格控制鋁板產品的質量,如果您對鋁板有要求,請聯系我們的銷售經理,給您一個全面的解決方案。
  Aluminum plate manufacturers strictly control the quality of aluminum plate products. If you have requirements for aluminum plate, please contact our sales manager to give you a comprehensive solution.

精品羞羞答答| 日韩欧美成人视频免费观看| 欧美成人日韩精品午夜| 内射网站在线搜索资源| 色大师懂色AV| 亚洲日韩欧美熟女| 成年丰满熟妇午夜免费视频| 草b日b搞b干bc| 2020最新毛片网站| 国产白浆一区二区三区四区| 亚洲tjwuynalousn一区| 哦美去干网| 迁西县| 然后欧美在线一区二区| 国产欧美剧情主播瑜伽丝袜另类 | 99精品资源亚洲| 夜区一区二区三区| 人妻少妇后入AV| 久久久久久久久8久久久| 日本啪啪啪午夜一区二区| 黄色AAA久久| 牙克石市| 美人妻的丝袜一区| 丰满少妇人妻一区二区三区在线视频| 日本色女视频| 青青草AV成人| 欧洲亚洲av在线免费观看| 啊啊阿啊啊啊好大好爽| 婷婷的八十区按摩| 久久视频日本韩国国产| 大香蕉A片一区二区| 午夜福利毛片免费观看| 国产精品久久宾馆| 深爱综合在线激情视频| 黄色涩涩国产| 日韩精品大香蕉| 日韩91久久中文字幕| 熟女人妻第10页| 粉色午夜福利视频| 91www你懂我| 桃色av最新地址在线观看|